PA Trace / Guides

Sound system measurement glossary

The words that come up when measuring and tuning a sound system, each in a sentence or two, with a link to the guide that explains it properly.

Updated 17 November 2026

Acoustic center
The point a loudspeaker's sound appears to come from. For timing, distances are measured from it, not from the front of the box.
Arrival time
When the direct sound reaches the microphone, after the reference: the peak of the impulse response. About 2.9 ms per meter.
ASIO
A low-latency audio driver standard for Windows, supplied by the interface maker.
Averaging
Combining successive measurement frames to separate the system's response from noise. Deeper averaging is steadier but slower to react.
Banding
Summing spectrum energy into fractional-octave bands, from 1/1 to 1/48 octave, as an RTA does.
Calibration
Linking an input's dBFS to dB SPL with an acoustic calibrator. See microphone calibration.
Coherence (γ²)
The share of the measurement signal explained linearly by the reference, from 0 to 1: how far to trust a reading at each frequency. See coherence explained.
Comb filter
The regular row of notches caused by two copies of a signal arriving at different times. Two arrivals 1 ms apart notch at 500 Hz, 1.5 kHz, 2.5 kHz and so on.
Complex averaging
Vector averaging of the transfer function. It rejects noise unrelated to the reference and reads low where coherence is low.
Crossover
The frequency range where two sources or two ways of a loudspeaker share the signal. See how to align subs and tops.
dBFS
Decibels relative to the converter's full scale. 0 dBFS is the largest value the converter can represent.
dB SPL
Sound pressure level in decibels relative to 20 µPa. 94 dB SPL is 1 Pa.
Delay (inserted)
The delay the analyzer applies to the reference so it lines up with the arrival at the microphone. Without it the phase is unreadable.
Dual-channel measurement
Comparing two signals, the reference sent to the system and the microphone, so the result shows the system regardless of the program.
EDT
Early decay time: the first 10 dB of a room's decay, scaled to 60 dB. Closer to perceived reverberance than RT60.
ETC
Energy-time curve: the envelope of the impulse response in dB. The usual view for reading arrivals and decay.
FFT
Fast Fourier Transform: turns a block of samples into a spectrum. Its size sets the frequency resolution and the time window. See FFT size and time windows.
Group delay
The arrival time of each frequency, from the slope of the phase, in milliseconds.
Impulse response
The system's output for an ideal click: the transfer function seen in time. See how to measure a room.
Leq
Equivalent continuous level: the steady level with the same energy as a varying one over a stated time. Most level limits are written as an Leq. See SPL monitoring.
Magnitude
The gain of the system at each frequency, in dB relative to the reference.
MTW (multi-time window)
A transfer function analysis that measures each octave with a time window suited to it: long windows at low frequencies, short ones at high. PA Trace's version is MTW++.
Narrowband
A spectrum shown at the FFT's own resolution, without banding.
Phase
The time shift of each frequency, in degrees of its own cycle. 360° is one full cycle.
Pink noise
Random noise with equal energy per octave. It reads flat on a banded RTA and is the standard test signal.
Polar averaging
Magnitude from the averaged powers of the two signals. It reads the level a listener hears, noise included.
Polarity
The sign of a signal. A reversed source pushes where the others pull. See how to check polarity.
Reference
The signal the system under test receives, taken as the transfer function's input. See measurement setup.
Room mode
A low-frequency resonance of a room, strong at some positions and weak at others.
RT60
Reverberation time: how long sound takes to decay by 60 dB, usually extrapolated from a 20 dB (T20) or 30 dB (T30) range.
RTA
Real-time analyzer: the spectrum of a single signal, without a reference.
Schroeder curve
The backward-integrated energy decay of an impulse response, from which reverberation times are read.
Smoothing
Averaging each point with its neighbors over a fractional octave, for display only.
STI
Speech Transmission Index (IEC 60268-16), from 0 to 1: how intelligible speech will be at a position.
Target curve
The response a system is tuned toward, usually with a tolerance band. See how to EQ a PA system.
Trace
A stored copy of a measurement's result, kept for comparison, averaging and documentation.
Transfer function
H(f) = Y(f) / X(f): what a system does to each frequency, in level and in time. See transfer function explained.
Weighting (frequency)
A curve applied to a measurement to follow the ear or a standard, such as A or C.
Window (FFT)
The fade applied to each analysis block, such as Hann; also the block's length in time.
Wind Lock
PA Trace's alignment of each measurement frame to the running average before averaging, so wind does not wash out the top octaves.
  • Transfer function measurement, explained Magnitude, phase, coherence and the impulse response: what they are and how to read them.
  • Coherence explained What the coherence trace means, what each pattern of low coherence points to, and how to raise it.
  • Measurement setup Microphone, interface, where to take the reference, and the levels that make a measurement trustworthy.
  • Room acoustics: RT60 and STI Read the impulse response, measure reverberation time, clarity and speech intelligibility, and find the surface behind a reflection.